Diferencia entre revisiones de «Unimod B1: Assembling»

De WikiRobotics
Saltar a: navegación, buscar
(Steps 0-3: The same than for the Unimod A1)
(Paso 4: Atornillar el módulo MY1 a la Skycube)
Línea 32: Línea 32:
 
* '''Step 3''': [[Unimod_A1:_Assembling#Step_3:_Screw_the_Skycube_board_to_the_part_D|Screw the Skycube board to the part D]]
 
* '''Step 3''': [[Unimod_A1:_Assembling#Step_3:_Screw_the_Skycube_board_to_the_part_D|Screw the Skycube board to the part D]]
  
=== '''Paso 4''': <font color=blue>Atornillar el módulo MY1 a la Skycube</font> ===
+
=== '''Step 4''': <font color=blue>Screw the MY1 module to the Skycube board</font> ===
 +
 
 
{| {{tablabonita}}  
 
{| {{tablabonita}}  
| [[Imagen:Icono_aviso.png]] <font color=red>¡MUY IMPORTANTE!</font> Colocar el módulo encima de la Skycube con la misma orientación mostrada en la foto.  
+
| [[Imagen:Icono_aviso.png]] <font color=red>IMPORTANT!</font> Place the module on top the Skycube board in the same orientation shown in the picture.  
 
|}
 
|}
 +
  
 
{|
 
{|
|| [[Imagen:Unimod-B1-paso4-1.jpg|thumb|300px|Tarjeta Skycube atornillada a la pieza D y al portapilas, Módulos MY1 y 4 tornillos ''(Click para ampliar)'']]
+
|| [[Imagen:Unimod-B1-paso4-1.jpg|thumb|300px|Skycube board screwed both to part D and to the battery pack, one MY1 module and 4 bolts ''(Click to enlarge)'']]
|| [[Imagen:Unimod-B1-paso4-2.jpg|thumb|300px|Atornillar el Módulo MY1 a la Skycube. '''¡Respectar la misma orientación que en la foto!''' ''(Click para ampliar)'']]
+
|| [[Imagen:Unimod-B1-paso4-2.jpg|thumb|300px|MY1 module on top of Skycube. '''Respect the same orientation shown in the picture!''' ''(Click to enlarge)'']]
 
|------------
 
|------------
|| [[Imagen:Unimod-B1-paso4-3-r1.jpg|thumb|300px|Módulo atornillado ''(Click para ampliar)'']]
+
|| [[Imagen:Unimod-B1-paso4-3-r1.jpg|thumb|300px|Screw the module to the Skycube board ''(Click to enlarge)'']]
 
|}
 
|}
  

Revisión del 07:55 23 feb 2011

Unimod type B1 (click to enlarge)

Introduction

Unimod is the minimal module capable of oscillating autonomously. To assembly it the following parts are needed:

  • One MY1 module fully assembled (Assembly instructions)
  • One Skycube board
  • One flat battery pack for 4 AAA batteries ready to use (Instructions)
  • The part D
  • 4 male/female spacers. Size M3, length 12mm
  • 4 spacers (female/female). size M3, length 10mm
  • 8 M3 bolts. Length: 6mm
  • 2 M3 falt head bolts. Length: 8mm.
  • 2 M3 nuts


Beginning: Parts needed to mount one UNIMOD type B1 (Click to enlarge)
End: One Unimod type B1 finished (Click to enlarge)

Assembling

Icono aviso.png IMPORTANT! If one Unimod type A1 has already been mounted and we want to build a new Unimod type B1 from it, just unscrew the MY1 module and rotate it 90 degrees clockwise.

Steps 0-3: The same than for the Unimod A1

The step from 0 to 3 are exactly the same than for assembling Unimod type A1:

Step 4: Screw the MY1 module to the Skycube board

Icono aviso.png IMPORTANT! Place the module on top the Skycube board in the same orientation shown in the picture.


Skycube board screwed both to part D and to the battery pack, one MY1 module and 4 bolts (Click to enlarge)
MY1 module on top of Skycube. Respect the same orientation shown in the picture! (Click to enlarge)
Screw the module to the Skycube board (Click to enlarge)

Paso 5: Conectar el servo y la alimentación

  • Conectar el servo a la Skycube, en cualquier de los conectores rectos, correspondientes a los servos 2, 4, 6 u 8. El cable negro del servo tiene que apuntar hacia el switch rojo de on-off.
Conectar el servo, con la misma orientación mostrada en la foto (Click para ampliar)
Conectar la alimentación (Click para ampliar)

Paso 6: Poner las pilas

  • Por último, colocar las 4 pilas AAA en el portapilas y encender Unimod para comprobar que la conexión se ha hecho correctamente. El led rojo de power on se deberá encender.
Unimod con las 4 pilas AAA colocadas (Click para ampliar)
Unimod encendido (Click para ampliar)

Fotos

Álbum de fotos

Enlaces

Noticias

  • 05/Abril/2010: Primera versión de la página terminada
  • 04/Abril/2010: Comenzada esta página