Diferencia entre revisiones de «Cube3: Assembling»
De WikiRobotics
(→Introduction) |
(→Montaje) |
||
Línea 13: | Línea 13: | ||
|} | |} | ||
− | == | + | == Assembling == |
− | === ''' | + | === '''Step 0''': <font color=blue>Perform the previous assembly</font> === |
− | + | To assembly [[Robot Modular: Cube3|Cube3]] it is necessary to first build the following parts: | |
− | # [[Minicube-I: Montaje| | + | # [[Minicube-I: Montaje|Build Minicube-I]] |
− | # [[Módulos MY1:Montaje| | + | # [[Módulos MY1:Montaje|Build one MY1]] |
{| | {| | ||
− | || [[Imagen:Minicube-I-fin-r2.jpg|thumb|300px| | + | || [[Imagen:Minicube-I-fin-r2.jpg|thumb|300px|Build Minicube-I (''Click to enlarge'')]] |
− | || [[Imagen:Modulo-y1-lote1-1.jpg|thumb|250px| | + | || [[Imagen:Modulo-y1-lote1-1.jpg|thumb|250px|Assemble one MY1 (''Click to enlarge'') ]] |
|} | |} | ||
− | === ''' | + | === '''Step 1''': <font color=blue>Screw the module to Minicube-I</font> === |
{| | {| | ||
− | || [[Imagen:Cube3-inicio-r2.jpg|thumb|300px| '''1)''' Minicube-I, | + | || [[Imagen:Cube3-inicio-r2.jpg|thumb|300px| '''1)''' Minicube-I, one MY1 module and 4 bolts and nuts ''(Click to enlarge)'']] |
− | || [[Imagen:Montaje-Cub3-Paso1-1-r1.jpg|thumb|center|200px| '''2)''' | + | || [[Imagen:Montaje-Cub3-Paso1-1-r1.jpg|thumb|center|200px| '''2)''' Screwing the MY1 module to the Minicube-I robot ''(Click to enlarge)'']] |
|-------------- | |-------------- | ||
− | || [[Imagen:Montaje-Cube3-Paso1-2-r1.jpg|thumb|300px| '''3)''' Minicube-I | + | || [[Imagen:Montaje-Cube3-Paso1-2-r1.jpg|thumb|300px| '''3)''' Minicube-I is screwed to the MY1 module ''(Click to enlarge)'']] |
− | || [[Imagen:Montaje-Cub3-Paso1-3-r1.jpg|thumb|300px| '''4)''' | + | || [[Imagen:Montaje-Cub3-Paso1-3-r1.jpg|thumb|300px| '''4)''' The cube3 robot is ready ''(Click to enlarge)'']] |
|} | |} | ||
Revisión del 05:34 23 feb 2011
Contenido
Introduction
Cube3 is a 1D topology pitch-pitch modular robot. It consist of three modules. For assembling it the following parts are needed:
- One MY1 module (Assembly instructions)
- One Minicube-I robot (Minicube-I: Assembling)
- 4 M3 bolts
- 4 M3 nuts
Assembling
Step 0: Perform the previous assembly
To assembly Cube3 it is necessary to first build the following parts:
Step 1: Screw the module to Minicube-I
Paso 2: Conectar el servo a la Skycube
Conectar el servo del módulo a la Skycube. Se puede conectar en cualquiera de los conectores libres
¡MUY IMPORTANTE! Conectar el servo en la orientación correcta. El cable negro apuntando hacia arriba. |
Paso 3 (Opcional) Fijar los cables con bridas
Opcionalmente, se pueden usar bridas para fijar los cables. Este paso es similar al paso 3 del montaje de Minicube-I
Fotos
Álbum de fotos |
Enlaces
Noticias
- 03/Abril/2010: Primera versión terminada
- 31/Marzo/2010: Comenzada esta página