Diferencia entre revisiones de «Cube3: Assembling»

De WikiRobotics
Saltar a: navegación, buscar
(Montaje)
(Noticias)
 
(No se muestran 5 ediciones intermedias del mismo usuario)
Línea 36: Línea 36:
 
|}
 
|}
  
=== '''Paso 2''': <font color=blue>Conectar el servo a la Skycube</font> ===
+
=== '''Step 2''': <font color=blue>Connect the servo to the Skycube board</font> ===
Conectar el servo del módulo a la Skycube. Se puede conectar en cualquiera de los conectores libres
+
Connect the module's servo to the Skycube board. It can be connected to any of the free 3-pin headers
  
 
{| {{tablabonita}}  
 
{| {{tablabonita}}  
| [[Imagen:Icono_aviso.png]] <font color=red>¡MUY IMPORTANTE!</font> Conectar el servo en la orientación correcta. El cable negro apuntando hacia arriba.
+
| [[Imagen:Icono_aviso.png]] <font color=red>IMPORTANT!</font> Connect the servo in the correct orientation. The black wire should be pointing upwards
 
|}
 
|}
  
  
 
{|
 
{|
|| [[Imagen:Montaje-Cube3-paso2-1.jpg|thumb|300px| '''1)''' Skycube con los tres servos conectados ''(Click para ampliar)'']]
+
|| [[Imagen:Montaje-Cube3-paso2-1.jpg|thumb|300px| '''1)''' The skycube board with three connected servos  ''(Click to enlarge)'']]
|| [[Imagen:Montaje-Cube3-Paso2-2.jpg|thumb|300px| '''2)''' Cube3 terminado''(Click para ampliar)'']]
+
|| [[Imagen:Montaje-Cube3-Paso2-2.jpg|thumb|300px| '''2)''' Cube3 is finished''(Click to enlarge)'']]
 
|}
 
|}
  
=== '''Paso 3''' (Opcional) <font color=blue>Fijar los cables con bridas</font> ===
+
=== '''Step 3''' (Optional) <font color=blue>Secure the wires with cable ties</font> ===
  
Opcionalmente, se pueden usar bridas para fijar los cables. Este paso es similar al [[Minicube-I:_Montaje#Paso_3_.28Opcional.29_Fijar_los_cables_con_bridas|paso 3 del montaje de Minicube-I]]
+
Optionally, cable ties can be used to secure the wires. This step is similar to [[Minicube-I:_Assembling#Step_3_.28Optional.29_Secure_the_cables_using_cable_ties]]
  
 
{|
 
{|
|| [[Imagen:Montaje-Cube3-Paso3-1.jpg|thumb|300px| '''1)''' Colocando una brida para fijar los cables ''(Click para ampliar)'']]
+
|| [[Imagen:Montaje-Cube3-Paso3-1.jpg|thumb|300px| '''1)''' Placing a cable tie for securing the wires ''(Click to enlarge)'']]
|| [[Imagen:Montaje-Cube3-Paso3-2.jpg|thumb|300px| '''2)''' Cube3 con bridas''(Click para ampliar)'']]
+
|| [[Imagen:Montaje-Cube3-Paso3-2.jpg|thumb|300px| '''2)''' The Cube3 robot with cable ties''(Click to enlarge)'']]
 
|}
 
|}
  
== Fotos ==
+
== Pictures ==
  
 
{| {{tablabonita}}
 
{| {{tablabonita}}
|| [http://fotos.iearobotics.com/index.php?album=robot-modular-cube3 Álbum de fotos]
+
|| [http://fotos.iearobotics.com/index.php?album=robot-modular-cube3 Photo album]
 
|}
 
|}
  
== Enlaces ==
+
== Links ==
 +
* [[Training on modular snake robots|Training on modular snake robots (Main page)]]
 
* [[Robot Modular: Cube3]]
 
* [[Robot Modular: Cube3]]
 
* [[Robot Modular:Minicube-I|Minicube-I]]
 
* [[Robot Modular:Minicube-I|Minicube-I]]
 
* [[Unimod]]
 
* [[Unimod]]
* [[Módulos MY]]
+
* [[Módulos MY|MY1 modules]]
* [[Skycube|Tarjeta Skycube]]
+
* [[Skycube|Skycube board]]
  
== Noticias ==
+
== News ==
  
* '''03/Abril/2010''': Primera versión terminada
+
* '''23/Feb/2011''':  This page is created!
* '''31/Marzo/2010''':  Comenzada esta página
 
  
 
[[Categoría:Robots modulares]]
 
[[Categoría:Robots modulares]]

Revisión actual del 05:42 23 feb 2011

The Cube3 robot, with 3 MY1 modules

Introduction

Cube3 is a 1D topology pitch-pitch modular robot. It consist of three modules. For assembling it the following parts are needed:

Beginning: Parts needed for assembling Cube3 (Click to enlarge)
End: Cube3 robot (Click to enlarge)

Assembling

Step 0: Perform the previous assembly

To assembly Cube3 it is necessary to first build the following parts:

  1. Build Minicube-I
  2. Build one MY1
Build Minicube-I (Click to enlarge)
Assemble one MY1 (Click to enlarge)

Step 1: Screw the module to Minicube-I

1) Minicube-I, one MY1 module and 4 bolts and nuts (Click to enlarge)
2) Screwing the MY1 module to the Minicube-I robot (Click to enlarge)
3) Minicube-I is screwed to the MY1 module (Click to enlarge)
4) The cube3 robot is ready (Click to enlarge)

Step 2: Connect the servo to the Skycube board

Connect the module's servo to the Skycube board. It can be connected to any of the free 3-pin headers

Icono aviso.png IMPORTANT! Connect the servo in the correct orientation. The black wire should be pointing upwards


1) The skycube board with three connected servos (Click to enlarge)
2) Cube3 is finished(Click to enlarge)

Step 3 (Optional) Secure the wires with cable ties

Optionally, cable ties can be used to secure the wires. This step is similar to Minicube-I:_Assembling#Step_3_.28Optional.29_Secure_the_cables_using_cable_ties

1) Placing a cable tie for securing the wires (Click to enlarge)
2) The Cube3 robot with cable ties(Click to enlarge)

Pictures

Photo album

Links

News

  • 23/Feb/2011: This page is created!